Storage tanks
Cylindrical sheet tanks
- single wall
- double wall

What we do
Conception of your installation
Of the simple pricking up to the most complex equipment realized to measure, a safe and proven range of accessories.
- Footbridges and gantry
- ladders, stairs
- Manhole, vent
- Nozzle,…
- Level with ballcock or analog
- Reheating by pin
- Reheating by immersion heater
Footbridges, ladders, stairs, gantry….
A complete range made to your measurments.
Designed following a precise analysis of needs, the tanks and other equipment (gas scrubber or deodorizing tower, range for valves and other instruments, boiler making works, PEHD, PPH, PVC, polyester or stainless, etc. piping) for storing and retaining corrosive chemicals in complete safety. They are also usually integrated for protecting, securing, diluting, and neutralizing (effluent depollution and neutralization installations).
Spiral wind extrusion Spécial high volumes
- Process: extrusion-rolling-up Homogeneity
- No oxidation between layers Variable thickness zones Produced strongly corrosive
- Big volumes

Get a quote :
+33(0)4 42 12 51 72
Cylindrical sheet tanks
- single wall
- double wall
Process: welded sheet
Economic
Multi-purpose
Small volume
Diluted products
Mildly corrosive
Any diameters

Get a quote :
+33(0)4 42 12 51 72
Economical multi-purpose storage
Transformation by mechanical process, plate preparation on a digital cutting machine. Shaping is performed by arching and hot polyfusion assembly.
Process advantages
– Any type of tank diameter
– Enables storage of most corrosive liquids, low volume liquids
– Uses the simplest and most economical process
– Optimized dimensions
– Optimized costs for highway transport
– Complies with regulations in force
– For manufacturing double-jacket retentions, gas scrubbing towers, or all sorts of special parts
Retention design rules
Retention can be designed in a double jacket construction (PEHD or PP, tank + integrated retention) or in concrete (concrete retention pit with tank installed inside or placed on a pad).
– In concrete or double jacket construction, it must have an available volume that can recover the entire volume of the full tank in the event it fails.
– If there are multiple single jacket tanks to be installed, the volume of the concrete retention pit must equal 50% of the total volume of the tanks or the volume of the largest tank.
More informations :

PEHD, PP: versatility and resistance
The chemical inertia of the PEHD (high-density polyethylene) and the PP (polypropylene) guarantees a reliable storage of the chemical, corrosive and dangerous products. After rinsing, a tank can, for example, receive alternately from the washing of soda and from some hydrochloric acid. Thus they are extremely multi-purpose.
Safety for the storage of the most dangerous products
Our vertical tanks are made by extrusion-rolling-up and meet the requirements of storage of the chemical industry and parachimique, pharmaceutical, of the water treatment and nuclear power.
They are intended for the storage of dangerous products, acids and bases concentrated, the acid and basic effluents, in ranges of temperatures going of -45°C in +90°C.
( See board of 20 most stored products)
Temperatures / Advantages PEHD PPH
The values which follow are indicative and can change according to the process of transformation and some manufacturing of the tested samples.


Diameter/Capacity
different diameters for a solution adapted to every dimensional imperative. The given diameters are chucks of rolling-up and correspond to the internal diameters of tanks.
Cylindrical heights are given for information purposes, any intermediate height is practicable on simple request.

Transformation by mechanical process, plate preparation on a digital cutting machine. Shaping is performed by arching and hot polyfusion assembly.
Process advantages
– Any type of tank diameter
– Enables storage of most corrosive liquids, low volume liquids
– Uses the simplest and most economical process
– Optimized dimensions
– Optimized costs for highway transport
– Complies with regulations in force
– For manufacturing double-jacket retentions, gas scrubbing towers, or all sorts of special parts
Manufacturing process European standard IN 12573-2
Processing by mechanical process, preparation of plates on a machine for digital cut. The shaping is assured by bending and the assembly by polyfusion under heat.
After this operation of assembly, the length of plate corresponds to the perimeter of the ferrule.

Retention can be designed in a double jacket construction (PEHD or PP, tank + integrated retention) or in concrete (concrete retention pit with tank installed inside or placed on a pad).
– In concrete or double jacket construction, it must have an available volume that can recover the entire volume of the full tank in the event it fails.
– If there are multiple single jacket tanks to be installed, the volume of the concrete retention pit must equal 50% of the total volume of the tanks or the volume of the largest tank.
Size of the single and double jacket

Size of single jacket tanks

Size of double jacket tanks

Footbridges
Footbridges
Staircases
Ladders
Guardrail
Platform


All the footbridges and the ladders are made in our premises to adapt itself to your project.
Characteristics
Profiles of structure are realized by process of pultrusion (hot polymerization of a profile stretched and contain until 70 % of fiberglass, what guarantees a high mechanical resistance. Their structure consisted of fiberglasses allows an excellent resistance (no permanent distortions due to the overloads).
Benefits
Rigidity
Corrosion resistance
Non-magnetic and not conductive
Lightness (three times less than the steel with equal rigidity)
